How to make a good backlight effect for TVs above 60 inches?

Product usages and skills, please come here.
Post Reply
support
Posts: 12
Joined: Mon Dec 23, 2019 8:20 am

How to make a good backlight effect for TVs above 60 inches?

Post by support » Tue Dec 31, 2019 12:17 pm

1. Raw Materials:
LED Strip Lights 16.4ft SMD2835 Multi-Color Kit

Fig 1: The products Price: $17.88 ; Specification: 5m, 300leds, waterproof, power consumption 6W~16W, 44Key infrared remote control ; Power Supply: 12V plug-in adapter with maximum output of 1.5A
1_Q2232VWFYUBDXZS.jpg
1_Q2232VWFYUBDXZS.jpg (160.77 KiB) Viewed 1701 times
2.Installation steps(demonstrating with a 60-inch TV set):

Fig2: Length Quick Look-up Table
1_FTKYEXPRWQFJYXH.jpg
1_FTKYEXPRWQFJYXH.jpg (39.96 KiB) Viewed 1700 times
(1) Determine the pasting solution

Before installing manually, it is necessary to determine the installation location, which is the basis for reliable and clean installation. Include:
  • Determine the position of the power cord and the controller. Here we need to pay attention to the position of the infrared probe to ensure that it is visible outside
  • According to the position of the controller, the starting point of the lamp tape sticking is determined, and then the installation direction and corner position of the lamp tape are determined
  • Determine four corners of the lamp strip
  • Determine positions for about 10 cm double-sided adhesive .
Tip: Why use so many double-sided adhesives?
Although the product is flexible, the torsion generated at the turning point will exceed the adhesive force of the strip itself. Therefore, it is necessary to set two strong double-sided adhesives at a certain distance(greater then 5cm) from the turning point.

You can refer to Fig 2 to calculate paste positions. Fig 3 is the result of location determination.

Fig 3: Install Postions
1_AH8S68P9XWKPA7F.jpg
1_AH8S68P9XWKPA7F.jpg (51.48 KiB) Viewed 1700 times
(2) Cut out and set up double-sided glues for pre-selected positions
1_5RDBZ2ACWFVNVRE.jpg
1_5RDBZ2ACWFVNVRE.jpg (70.13 KiB) Viewed 1700 times
1_Z49TUZK3F9E4N7Z.jpg
1_Z49TUZK3F9E4N7Z.jpg (26.4 KiB) Viewed 1700 times
(3) Paste the lamp strip, pay attention to the accurate installation of the lamp tape on the double-sided adhesive

(4) While processing at corner, pay attention to the twisting method of the lamp strip
1_BGNAVR5MEQUN25X.jpg
1_BGNAVR5MEQUN25X.jpg (50.13 KiB) Viewed 1700 times
1_GP53KV9C4CB2XCJ.jpg
1_GP53KV9C4CB2XCJ.jpg (41.77 KiB) Viewed 1700 times
(5) Paste controller after install special double-sided adhesive paper
1_KRAAQ855CNA6AMM.jpg
1_KRAAQ855CNA6AMM.jpg (26.2 KiB) Viewed 1700 times
1_6H26YNEWMX4WP47.jpg
1_6H26YNEWMX4WP47.jpg (17.28 KiB) Viewed 1700 times
6) Finally, connect the controller with the lamp belt, connect the power supply to the controller, and control the lamp with the remote control

End, enjoy and take photos or videos to share with your friends!

Post Reply